FUDforum
My FUDforum

Home »  » Managed Industrial Ethernet Switches » Can't Upgrade Firmware
Can't Upgrade Firmware [message #330] Thu, 13 August 2015 16:49 Go to next message
ksperle is currently offline  ksperle
Messages: 3
Registered: June 2014
Junior Member
out today with one that I did a "Load Default" on. Will see what happens with the new one. Also - will bring the other back to my office and leave on and see what happens when it runs off of the network.

Thanks,
Chris
Hi Chris,

I was informed about a newer firmware for the ES8520-XT this morning. Our testers will be downloading it to test on a switch. However, they have been unable to replicate the issue. I will let you know when the new firmware is available

KurtThanks Kurt - I'm still having the issue and not able to determine what is different on a good one/bad one so maybe a new firmware will help. Let me know when it is available for us
Re: Can't Upgrade Firmware [message #331 is a reply to message #330] Fri, 14 August 2015 09:01 Go to previous messageGo to next message
Mac is currently offline  Mac
Messages: 297
Registered: February 2014
Power User
e.

Thanks
Hi, I just followed up with the people testing the firmware. So far it is going well and should be available by the end of these week assuming no problems occur.

KurtGreat! Thank you!
I have the firmware. What email would you like me to send it to? You can send an email to me if you want with the info. My email would be krees{at]us.pepperl-fuchs.comKurt - i emailed you my email address.
Thanks Kurt - got the firmware. WIll give it a try.

what is the System OID? just curious what version that should be at? Mine says version: 1.3.6.1.4.2882.2.2.24
j


Mac Harned, CNE, MCP, KCE | Technical Support
www.comtrol.com
http://forum.comtrol.com

Comtrol Corporation
100 Fifth Ave NW
Minneapolis, MN. 55112
Direct 763.957.6000 | Fax 763.957.6001
connect. communicate. control
Re: Can't Upgrade Firmware [message #332 is a reply to message #331] Fri, 14 August 2015 10:14 Go to previous messageGo to next message
ksperle is currently offline  ksperle
Messages: 3
Registered: June 2014
Junior Member
ust want to make sure that is correct.Hi Chris,

You should be ok. The SNMP server should see the switch in the network management system.Ok - so it has to do with network management? We are not doing any network managmeent so we don't have to worry about it then?

-Chris
That is correct. Let me know how things go after the firmwar
Re: Can't Upgrade Firmware [message #333 is a reply to message #332] Fri, 14 August 2015 10:53 Go to previous messageGo to next message
ksperle is currently offline  ksperle
Messages: 3
Registered: June 2014
Junior Member
e is loaded.

KurtHi,

I'm following up with you. Has the firmware improved things?

Thanks,
KurtNo - I'm still having the problem.

I think I've been able to recreate here internally (the other switches have been out in the field so have been harder to troubleshoot as its about -4 degrees out!

Report message to a moderator

Re: Can't Upgrade Firmware [message #334 is a reply to message #333] Fri, 14 August 2015 10:59 Go to previous message
Mac is currently offline  Mac
Messages: 297
Registered: February 2014
Power User
gif" border="0" alt="Wink" />.
The switch that I've had it happen to here I'm attached to via a Cat5 cable directly to the core switch (Cisco 3750). So I'm hoping to be able to try more things. Could it have

Mac Harned, CNE, MCP, KCE | Technical Support
www.comtrol.com
http://forum.comtrol.com

Comtrol Corporation
100 Fifth Ave NW
Minneapolis, MN. 55112
Direct 763.957.6000 | Fax 763.957.6001
connect. communicate. control
Previous Topic: Getting error when logging into switch through telnet
Next Topic: System information not shown on the home page of a RocketLinx Switch
Goto Forum:
  


Current Time: Tue May 18 12:03:48 CDT 2021

Total time taken to generate the page: 0.01065 seconds